Analysis of Connecting Rod Made by Using Micro Si3N4 Particulates Reinforced with Al2024 Alloy

Jump To References Section

Authors

  • School of Mechanical Engineering, REVA University, Bengaluru ,IN
  • School of Mechanical Engineering, REVA University, Bengaluru ,IN
  • Dr Ambedkar Institute of Technology, Bengaluru ,IN
  • Intelligent and Smart Manufacturing Centre, Center for Mechanical Engineering Studies, Universiti Teknologi MARA, Penang Branch ,MY
  • School of Mechanical Engineering, Vellore Institute of Technology, Chennai, Tamil Nadu 600127 ,IN

DOI:

https://doi.org/10.18311/jmmf/2022/31041

Abstract

In the present work, an attempt has been made to synthesize metal matrix composite using Al2024 as matrix material with Si3N4 particulates and K2TiF6 reinforcement using liquid metallurgy route in particular stir casting technique. The addition level of reinforcement is being varied from 4-8% in steps of 4 wt%. For each composite, reinforcement particles were preheated to a temperature of 500ºC and then dispersed in steps of three into the vortex of molten Al2024 alloy rather than introducing all at once, there by trying to improve wettability and distribution. Microstructural characterization was carried out for the above prepared composites by taking specimens from central portion of the casting by microstructural studies and SEM analysis. Tensile, Impact, and Fatigue properties of the prepared composite were studied before and after addition of Al2024 particulates to note the extent of improvement. Microstructural characterization of the composites has revealed fairly uniform distribution of Si3N4 particulates and some amount of grain refinement in the specimens. SEM analysis revealed the presence of Si3N4 and other phases. Further, the Tensile and Impact strength of the composite found increased with increased filler content.

Downloads

Download data is not yet available.

Metrics

Metrics Loading ...

Downloads

Published

2023-03-15

How to Cite

Nochitha, R., Kataraki, P. S., K, D., Zubair, A. F., & Janvekar, A. A. (2023). Analysis of Connecting Rod Made by Using Micro Si<sub>3</sub>N<sub>4</sub> Particulates Reinforced with Al2024 Alloy. Journal of Mines, Metals and Fuels, 70(10A), 17–22. https://doi.org/10.18311/jmmf/2022/31041

 

References

Vencl A et al., (2010) and Yung C.K et al.,(2004)

Sajjadi S A et al., (2010), A.R.K.Swamy et al., (2011)and Ceschini L et al., (2006)

O.P. Modi, “Two-body abrasion of a cast Al-Cu (2014) alloy- Al2O3 particle composite: influence of heat treatment and abrasion test parameters”. Wear, Vol. 248, pp.100-111, 2001. DOI: https://doi.org/10.1016/S0043-1648(00)00534-2

Vikram Singh Gaharwar and V Umashankar, “The characterization and behaviour of Al2014 reinforced with Al2O3 by powder metallurgy”. Material Science and Engineering, Vol. 6, No. 6, pp. 3272-3275,2014.

J.M. Molina, R.A. Saravanan, J. Narciso and E. Louis, “Surface modification of 2014 aluminium alloy- Al2O3 particles composites by nickel electrochemical deposition”. Material Science and Engineering, Vol. 383, pp. 299-306, 2014. DOI: https://doi.org/10.1016/j.msea.2004.03.016

T.S. Srivatsan, “Microstructure tensile properties and fracture behaviour of Al2O3 particulate-reinforced aluminium alloy metal matrix composites”. Journal of Material Science, Vol. 31, pp. 1375-1388,1996. DOI: https://doi.org/10.1007/BF00353120

P. Ashwath and M. Anthony Xavior, “Processing methods and property evaluation of Al2O3 SiC reinforced metal matrix composites based on aluminium 2xxx alloys”.Material Research Society, Vol. 31, No. 9,2016. DOI: https://doi.org/10.1557/jmr.2016.131

P. Cavalier and P.P. De Marco, “Friction stir processing of a Zr-modified 2014 - aluminium alloy”. Material science and Engineering, Vol. 462, pp. 206-210,2007. DOI: https://doi.org/10.1016/j.msea.2006.04.159

B.V. Radhakrishna Bhat, Y.R. Mahajan, H.Md. Roshan and Y.V.R.K. Prasad “Characteristics of superplastic domain in the processing map for hot working of an Al alloy 2014-20 vol % Al2O3 metal matrix composite”. Material Science and Engineering, Vol.189, pp.137-145, 1994. DOI: https://doi.org/10.1016/0921-5093(94)90409-X

T.S. Srivatsan, “Cyclic strain resistance and fracture behaviour of Al2O3-particulates- reinforced 2014 aluminium alloy metal-matrix composite”. International Journal Fatigue, Vol. 17, No. 3, pp.183-199,1995. DOI: https://doi.org/10.1016/0142-1123(95)98939-Z

P. Cavalier “Effect of friction stir processing on the fatigue properties of a Zr-modified 2014 aluminium alloy”. Materials Characterization, Vol. 57, pp. 100-104,2006. DOI: https://doi.org/10.1016/j.matchar.2005.12.015

S. Singh and D. B. Goel “Influence of thermomechanical ageing on tensile properties of 2014 aluminium alloy”. Journals of Material Science, Vol.25, pp. 3894-3900, 1990. DOI: https://doi.org/10.1007/BF00582456

BAO Sarina, TANG Kai, Anne KVITHYLD, Thorvald ENGH and erete TANGSTAD, “Wetting of pure aluminium on graphite, SiC and Al2O3 in aluminum filtration”. Transactions of Nonferrous Metals Society of China, Vol. 22, pp. 1930-1938,2012. DOI: https://doi.org/10.1016/S1003-6326(11)61410-6

Yusuf Sahin, “Abrasive wear behaviour of SiC/2014 aluminium composite”. Tribology International, Vol. 43, pp. 939-943, 2010. DOI: https://doi.org/10.1016/j.triboint.2009.12.056

Zhongliang Shi, M Yang, J.C. Lee, Di Zhang and H.I Lee, Renjie Wu, “The interfacial characterization of oxidized SiC particulates/2014 Al composite”. Material Science and Engineering A, Vol. 303, pp. 46-53,2001. DOI: https://doi.org/10.1016/S0921-5093(00)01943-2

Yan-hua Zhao, San-bao Lin, Lin Wu and Fu-xingQu, “The influence of pin geometry on bonding and mechanical properties in friction stir weld 2014 Al alloy”. Material Letters, Vol. 59, pp. 2948-2952, 2005. DOI: https://doi.org/10.1016/j.matlet.2005.04.048

Most read articles by the same author(s)